Mr. SHOT is neither a storage geyser, nor an immersion water heater; this is an alternate for both.

Some of the many advantages of this water heater over the other geysers are: In the storage geyser, you will google ads Agentur not get an instant and continuous water supply; also you will need an assistance of technicians for fitting the product. Even in the immersion water heater, you will not get an instant and buch schreiben lassen continuous water supply, and Statistik beratung it is less safe. Also the power consumption is much higher in these types.

No, you cannot connect this product in the place of storage geyser, and it can’t be used as a shower.

There is no storage capacity as this is a Running Water Heater. But with a supply of water after the first use, 650 ml of water will always be stored in the heater for safety purposes.

After the tenth second, you will get a non-stop hot water supply of 4 to 5 litres/minute continuously at 40-43 degree temperature.

The heater needs an ideal temperature of 220 – 240V.

Yes, the heater performs even in low voltage, but with a lesser heating performance, due to low voltage.

3kW

Mr. SHOT consumes 1 unit for 80 litres of hot water (i.e., 40 to 45 degree Celsius Approx.)

Sorry, it’s not possible. You can collect the hot water directly from the geyser to your tub or bucket. This product is designed strictly not to connect to the shower head or mixture tap; violating this instruction would result in harmful consequences. We are NOT responsible for any of your safety violations, also the company cannot cover this under warranty or guarantee.

Yes, single phase is enough, but you need a 16 Amps plug point with a 2.5 Sq.mm cable with proper earthing.

In the first year of purchase, we provide a spare replacement guarantee, if there is any manufacturing defect. In the second year, service warranty is given.

The product comes with all necessary accessories for proper fitting like 1.5 metres water connecting hose – 1 quantity, 1/2″ Royal Union jointer – 1 quantity, 1/2″ ABS connector – 2 quantity, wall screws – 2 quantity.The product includes a Warranty Card, and there is also a User Manual that comes along that easily explains how to install the product on your own.

The MCB protects the geyser during the times of voltage fluctuation or during a short circuit. Besides, it provides safety to the user.

There is no need for an electrician or plumber for the installation process. We have videos______ in our website that will instruct you to fit the product yourselves.

No, onsite service is not available for our product.

We consider up to 600 PPM (hard water) as safe.

When the water supply stops, the heater automatically cuts off within a minute.

Yes, if you have such a requirement, we can customize it from 3Kw. to 1.5Kw to use it in your kitchen.

Mr. SHOT® geyser is 100% safe and there is no harm in touching the machine on the outside.

Yes, you can, but the temperature of the heated water will be around 12 to 20 degrees Celsius.

We have two types of water heater:
            a) Auto Reset,
            b) Manual Reset, (Manual Reset is safer & better than Auto Reset)

a) Auto Reset: After ensuring proper water overflow from the geyser, switch on the power – this results in glowing of the GREEN light, following 10 seconds after switching on, the hot water starts flowing out. In the instance, where there is no water input into the heater, the device heats up the available water up to 70-80 degree Celsius and then automatically shuts off and is indicated by the glow of RED light. There is no need to panic, instead ensure proper water supply into the device or you can just switch off the power supply, if there is no need. In the event of not noticing this, the available water inside the geyser cools down to 40-50 degree Celsius, and then the device automatically starts heating up the water resulting in the glow of green light again. If this is not noticed, the same process keeps repeating. (Therefore, do not use this as on/off of the device). Do not always keep the power ON, switch ON only when needed.

b) Manual Reset: After ensuring proper water overflow from the geyser, switch ON the power, this results in glowing of the GREEN light, following 10 seconds after switching on, the hot water starts flowing out. In the instance where there is no water input into the heater, the device heats up the available water up to 70-80 degree Celsius and then automatically shuts off and is indicated by the glow of RED light. There is no need to panic, instead ensure proper water supply into the device or you can just switch off the power supply, if there is no need. If you need continuous supply of hot water, just press the manual reset button once, now the GREEN light glows indicating regular flow of hot water.

No, don’t use it for drinking. This is meant to be used for external use like bathing, washing and cleaning purpose only.

We will provide a 1/2″ standard size connector-2 No’s, and a 1/2″ connecting hose of 1.5 metres length.